Securing Deck Stair Treads

Installing treads is much like installing decking. Although with the stair treads, depending on the project details, you may have to decide on a tread pattern. Typical decking is 5-1/2 in. wide, but combining two boards is still a little narrow for a comfortable tread depth, especially when considering the overhang at the tread nosing. For wood decking, adding a 1-in. to 2-in. filler strip between the treads easily solves this issue.

There are a variety of ways to pattern the treads to make them wide enough for comfortable deck stairs. Adding a filler strip in the middle is both decorative and functional.

For composite decking, the solution can be a little more involved. For example, capstock decking looks different on the inside, so ripping a tread will show an obvious cut line. Similar difficulties arise with textured composite decking and metal decking. Some manufacturers have tread stock that solves this issue. Alternatively, placing the filler strip at the back to hide the cut face is another way to deal with this. 

Installing top-down fasteners

The most common way to secure decking on stairs is to face-screw the decking boards. Even if the main portion of the deck is secured with hidden fasteners, top-screwing the stair may still be a good option because hidden fasteners are sometimes difficult to use with stairs. Some composite decking types have tabs that fit over the screw holes to improve the appearance. In hardwood decking, you can hide the screw holes with plugs.

Wood plugs take a little extra work to install but effectively conceal fasteners. The key to success is ensuring you have a sharp Forstner bit to bore the countersink holes.

Before installing treads with top-down fasteners, first determine the amount of the overhang 1. Remember to account for the riser thickness when measuring the overhang. With the overhang set and the inside tread board in position, measure the width of the filler strip 2. Before installing the filler strip, round over the cut edge to give it a finished look 3.

To install the treads, align the inside board with the proper overhang by measuring back under the stringer 4. This distance will vary depending on your construction details.

1. Place the nosing tread in position with the correct overhang. Remember to account for the thickness of the riser.

2. Measure the gap between the treads and then subtract two times the standard decking gap to calculate the width of the filler strip.

3. Rip the filler strip to width and round over the cut edges.

4. Position the inside tread with the correct side overhang. Make a mark on the tread where it sits over the stringer’s centerline.

What can go wrong If you secure the deck board at the top of the stair permanently, the nosing overhang will force you to drive the fastener at an angle. Instead, leave the deck board loose so you can move it out of the way and drive the fastener straight down.

Another way to refine the deck’s appearance is to carefully line up the visible fasteners. Stack the treads with the ends aligned and transfer a layout mark that represents the stringer’s centerline 5. Before drilling any holes, mark the fastener locations and set up the boards for one tread to check the spacing 6. Once the distance between tread boards is established, cutting spacers is an easy way to keep the gaps uniform for the entire run of steps 7.

Align a gauge or Speed Square to the mark made in step 5 and make a slight indent with an awl 8. In hardwoods, the indent keeps the drill bit from wandering as you begin the hole. Drill the pilot hole using a 2-in-1 bit 9. Secure the tread boards before moving on to install the adjacent pieces 10. Align the filler strip with a spacer positioned over the stringer 11 and with a Speed Square to flush the ends 12.

5. Transfer that mark to the other tread pieces. Make sure the ends are aligned when doing this.

6. Mark the fastener spacing on one set of treads before you start drilling to check that the pattern is both functional and pleasing.

7. Rip spacers to the gap dimension. Hardwood spacers are more accurate and efficient than trying to measure the gap.

8. Make a pilot indentation with an awl. This marks the location and also prevents the drill bit from wandering off layout.

9. Drill both the pilot hole and countersink at the same time with a two-step drill bit

10. Secure the inside tread to the stringer with screws. Be careful not to overdrive the fastener.

11. Position the spacers between the treads to maintain a consistent gap.

12. Flush the tread ends with a square to eliminate any variation of the treads that would detract from the overall appearance.

Repeat the process to align and secure the outer tread board 13.

Working from the bottom tread up has the advantage that you have a finished platform to work from 14. To align the treads from one step to another place a square to reference the upper step with the lower step 15. After all the treads are installed, fit the risers, leaving any gap hidden under the overhang 16. Install the risers using the same method of aligning, drilling pilot holes, and securing as you did with the treads 17.

13. Secure the outside tread to the stringer; do not split the stringer.

14. Work up from the bottom when securing treads.

15. Align the ends of the treads with a square to keep a consistent layout.

16. Fit the risers after all the treads have been installed. Orient any gap to the top where it will be hidden by the overhang.

17. Secure the risers using the same layout methods you used with the treads.

Notch decking around posts Carefully fitting deck boards around posts and other objects will give the deck a professional look. You can do this without using a tape measure; instead, mark the tread in place referencing the side of the post or other obstruction. 1. Place the board you want to notch against the post with the end registered to its final installed position. Using a Speed Square, mark the perpendicular cutline. 2. Use a scrap piece of post material to mark the cut line that will be against the post’s forward face. 3. Mark the waste material with an X before moving the board. This will help you avoid the error of cutting to the wrong side of the line. It happens! 4. Use a chopsaw to make the partial perpendicular cut. The blade will not cut completely in the corner but you will finish the cut in the next step. 5. Make the adjoining cut with a jigsaw and finish both cuts at the corner. 6. Round the upper edge of the fresh cut with a trim router fitted with the same round-over bit that you used for easing the end cuts. Test-fit the board and make any adjustments necessary.

Fine Homebuilding Recommended Products

Jigsaw

When it comes to fitting and installing decking, a cordless jigsaw is a must-have for custom cuts — especially around posts.

Buy at Amazon

Standard Marking Chalk

We like white chalk because it’s non-permanent and wears off easily — this is especially helpful when marks are exposed and need to disappear.

Buy at Amazon

4-Gallon Piston Backpack Sprayer

This sprayer holds a large amount of solution and the backpack design keeps your hands free, making maintaining and cleaning a deck a breeze.

Buy at Amazon